Hampton Adjustable Mounted CryoLoop™ 20 micron蛋白结晶环

Hampton Adjustable Mounted CryoLoop™ 20 micron蛋白结晶环

可调悬挂式冷冻环™

APPLICATIONS

  • Cryocrystallography

应用:冰晶术

FEATURES

  • Adjustable loop orientation
  • Synthetic CryoLoop on adjustable stainless steel MicroTube
  • MicroTube specially engineered with EasySnap notches
  • 20 micron diameter nylon CryoLoop

特征:
可调回路定向
可调不锈钢微管上的合成冷冻环
EasySnap缺口专用微管
20微米直径尼龙冷冻环

DESCRIPTION

Similar to the Mounted CryoLoop™ in design and function, the Adjustable Mounted CryoLoop allows one to manipulate and orient the CryoLoop to multiple, unique positions previously unattainable with typical cryo setups. The Adjustable Mounted CryoLoop is a 20 micron diameter synthetic loop mounted inside a malleable stainless steel sleeve, which in turn, is mounted inside the EasySnap MicroTube™.

Using forceps or a probe one can manipulate the angle and orientation of the CryoLoop by bending and adjusting the angle of the malleable stainless steel insert which holds the CryoLoop. The Adjustable Mounted CryoLoop may be positioned several times. Note: Repeated manipulation will fatigue the sleeve which can lead to failure of the sleeve. The Adjustable Mounted CryoLoop is designed to work with the CrystalCap System components.

The MicroTube is 24 mm in length and is specially engineered with EasySnap™ notches at the 10, 12, 14, 18, and 21 mm measures. To obtain the desired length of MicroTube, simply snap the MicroTube at the desired length and stake it to the CrystalCap™ Magnetic or CrystalCap™ Copper Magnetic. These nylon loops show minimal diffraction, are thin for fast freezing, strong, and aerodynamic.

Most data collection geometries prefer or require a 22 mm length between the base of the cap and the beam. For a 22 mm overall length using the CrystalCap, CrystalCap ALS, CrystalCap ALS HT and CrystalCap SPINE HT, snap the MicroTube at the second notch from the bottom, creating an 18 mm MicroTube lenghth and secure to the CrystalCap using epoxy or similar adhesive. For a 22 mm over length using the CrystalCap Copper, CrystalCap Copper HT, CrystalCap ALS Copper HT snap the MicroTube at the fifth notch from the bottom (notch closest to the CryoLoop) and secure to the CrystalCap using epoxy or similar adhesive.

描述
在设计和功能上类似于安装的Cryoloop™,可调安装的Cryoloop允许一个人操纵和定位Cryoloop到以前无法用典型的冷冻装置达到的多个独特的位置。可调安装的冷冻环是一个20微米直径的合成环安装在一个可锻铸不锈钢套筒,这反过来,是安装在EasySnap微管™内。

使用钳子或探针,可以通过弯曲和调整可锻铸不锈钢刀片的角度来操纵冷冻环的角度和方向。可调安装的冷冻环可以定位几次。注:重复操作会使套筒疲劳,导致套筒失效。可调安装的冷冻环是设计与水晶帽系统的组成部分。

微管的长度是24毫米,是专门设计的EasySnap™缺口在10,12,14,18和21毫米的措施。要获得所需的微管长度,只需按所需长度将微管折断,并将其钉在晶体帽™磁性或结晶帽™铜磁性上。这些尼龙环显示最小的衍射,是薄的快速冻结,强大,空气动力学。

大多数数据收集几何学喜欢或需要22毫米的长度之间的盖子和梁。使用晶体帽、结晶帽ALS、结晶帽ALS HT和结晶帽脊骨HT的22 mm总长度,从底部的第二个缺口折断微管,用环氧树脂或类似的粘合剂制造18毫米的微管长度并固定在晶体帽上。使用结晶帽铜、结晶帽铜HT、结晶帽ALS铜HT超长22毫米,用环氧树脂或类似的粘合剂将第五个缺口处的微管从底部(最接近低温环的缺口)折断,并固定到结晶帽上。

HR4-336 Adjustable Mounted CryoLoop 0.025 – 0.05 mm – 25 pack
HR4-338 Adjustable Mounted CryoLoop 0.05 – 0.1 mm – 25 pack
HR8-102 Adjustable Mounted CryoLoop 0.1 – 0.2 mm – 25 pack
HR8-072 Adjustable Mounted CryoLoop 0.2 – 0.3 mm – 25 pack
HR8-104 Adjustable Mounted CryoLoop 0.3 – 0.4 mm – 25 pack
HR8-106 Adjustable Mounted CryoLoop 0.4 – 0.5 mm – 25 pack
HR8-108 Adjustable Mounted CryoLoop 0.5 – 0.7 mm – 25 pack
HR8-110 Adjustable Mounted CryoLoop 0.7 – 1.0 mm – 25 pack
HR5-900 Adjustable Mounted CryoLoop Sampler – 30 pack (5 of each diameter size 0.1 – 1.0 mm)